Pendant Face Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Jewel Eye Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Chili Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

5 Jeweled Bar Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Astra Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Titanium Cable Chain Double

Size: 30mm 

O-Ring: 2mm

Titanium Twist Chain

Sizes: 20mm  /  30mm  / 40mm

O-Ring: 2mm 

Titanium Cable Chain 

Sizes: 20mm  /  30mm  / 40mm

O-Ring: 2mm 

Bolt Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Dagger Dangle

1.8mm Internal Diameter Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Internally Threaded 0.9mm (Bottom) and Threadless (Top) Navel Bar

1.6mm (14g) x 10mm

Internally Threaded Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Daith Ruben Beaded Hinged Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

24kt Gold PVD Titanium Internally Threaded Bee Attachment 0.9mm (16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Internally Threaded Bee Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Internally Threaded Moon with Opal Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Internally Threaded Small Mix Color Flower Attachment 0.9mm Thread (For 16G)

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewel Oval Stone with Round Stone Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Crystal and Opal Jeweled Crown Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Moon With Cluster Stars Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Trio 4.5mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Smooth Snake Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Triplet Jeweled Spike Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless 5 Prong Set Ovate Jeweled Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless 9 Curved Prong Set Jeweled Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Trio 5mm Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

White 14kt Gold Threadless Opal                                                                                          Made out of solid 14kt Gold & implant grade steel pin. 4mm white fire cultured opal embedded in a solid 14kt gold cast.

Piece Size:  Length / 4mm  -  Width / 4mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

White Gold 14kt Threadless Prong Set 3mm Stone                                                              Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

White 14kt Gold Threadless Jewel Sword                                                                              Made out of solid 14kt Gold & implant grade steel pin. Tip to tip the beautify detailed sword is 9.1mm long and 4.3mm wide.

Piece Size:  Length / 9.1mm  -  Width / 4.3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

White 14kt Gold Threadless Moon & Opal                                                                                Made out of solid 14kt Gold & implant grade steel pin. Jeweled with 1.5mm white fire cultured opal.

Piece Size:  Length / 3.3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

White 14kt Gold Threadless Lunar                                                                                        Made out of solid 14kt Gold & implant grade steel pin. The 3 balls aside the crescent are 1mm each.

Piece Size:  Length / 3.4mm  -  Width / 3.5mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

White Gold 14kt Threadless Jeweled Bezel                                                                            Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.