Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Shiva                                                                              Made out of Nickle free solid 14kt Gold & implant grade steel pin. Shiva is a double piercing connected by solid 0.6mm 14kt gold chain. Each stone is 3mm princess cut. The full chain length stretched end to end is 50mm. Crystal to crystal pin chain length is 20mm. Followed by a 2.5mm petit hanging star.

Piece Size: Length / 20mm Piercing to Piercing - Width / 0.6mm - Chain

Pin Gauge: 0.42mm / Length: 4mm

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Nata                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. An ornate design with a 4.0mm crystal baguette. Nata features a trio of round 1.1mm crystal above and below the baguette.

Piece Size:  Length / 9mm  -  Width / 3.0mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Olek                                                                                   Made out of Nickle free solid 14kt Gold & implant grade steel pin. One of our favorites, Olek consists of 5 round prong set stones curved around the main piece.  A 23mm chain continues to a petit 1.7mm round crystal. Olek is designed for the right ear.  

Piece Size:  Length / 10.7mm -  Width / 1.2mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Emer                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. Emer is a 5.7mm round ring of genuine blue diamonds consisting of 16 prong set 1.2mm stones.

Piece Size:  Length / 5.7mm -  Width / 5.7mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Aura                                                                                  Made out of Nickel free solid 14kt Gold & implant grade steel pin. Aura is made of a total of 9 crystals. 4 marquise stone, 4 round 1mm crystals and a center aqua marine heart.  

Piece Size:  Length / 10.7mm -  Width / 10.7mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Kiana                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. Consisting of 5 crystals overlaying a black epoxy flower this design is unique in its depth and contrast.

Piece Size:  Length / 6.6mm -  Width / 6.6mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Marta Left                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. Three marquise stones alongside a 2mm round prong set crystal. 

Piece Size:  Length / 7.5mm  -  Width / 4.3mm 

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Disk Attachment                                                                                Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Gold 14kt Threadless Attachment Jeweled 3mm Bezel                                                    Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Opal Attachment                                                                               Made out of solid 14kt Gold & implant grade steel pin. 4mm white fire cultured opal embedded in a solid 14kt gold cast.

Piece Size:  Length / 4mm  -  Width / 4mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Solid Gold Earring With 5 Prong Set Crystals - Yana                                              Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Yana is a petit earing with five 1.7mm prong set crystals front facing followed by a 1.4mm gold band towards the rear.

Piece Size: Length / 8.7mm - Width / 8.7mm

Bar Gauge: 0.70mm / 21GA Length 4.3mm Internal Ring Size 6mm

14kt Solid Gold Earring Cuff & Chain - Rassa                                                                      Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Rassa is designed as a petit ear cuff at 1.9mm in thickness. Drop hanging at 11.5mm length a delicate solid 14kt chain to slight wrap around the ear placement. 

Piece Size:  Length / 9.3mm -  Width / 9.3mm 

Bar Gauge: 0.90mm / 19GA     Length 5.5mm                                                                      Internal Ring Size 6.8mm

14kt Gold Threadless Ring - Elsy                                                                                            Made out of solid 14kt Gold & implant grade steel pin. Elsy is designed as a petit ring but with the benefit of being threadless to allow it to fit into a labret for alternative placements. Elsy is the smaller option to the threadless ring designs with 13 round 1mm crystals pave the ring end to end .

Piece Size: Length / 7.6mm - Width / 1mm

Pin Gauge: 0.42mm / Length: 4mm*                                                                           Internal Ring Size - 5.1mm

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Nyla                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. Nyla is adorned with genuine 1.2mm diamond stones centered around a 2mm Garnet gemstone.  

Piece Size:  Length / 6.1mm  -  Width / 6.1mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Enya                                                                                   Made out of Nickle free solid 14kt Gold & implant grade steel pin. Enya is an alluring design of mixture shaped stones centered around a round aqua stone, 4 prong set baguettes aside 4 petit 1mm crystals.  

Piece Size:  Length / 9.1mm  -  Width / 9.1mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Olan                                                                                   Made out of solid 14kt Gold & implant grade steel pin. One of our favorites, Olan consists of 5 round prong set stones curved around the main piece.  A 23mm chain continues to a petit 1.7mm round crystal. Olan is designed for the left ear.  

Piece Size:  Length / 10.7mm -  Width / 1.2mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Tera                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. Tera is another one of our favorites. With a chain length of 20mm, at one end a 2.0mm round prong set stone & at the other a solid gold circlet dressed with a 1.5mm prong set crystal stone.

Piece Size: Length Chain / 20mm - Width / 4.4mm - Circlet

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Kaya                                                                                 Made out of Nickle free solid 14kt Gold & implant grade steel pin. Kaya is an arrow shape solid gold diamond incrusted piece consisting of ten 0.9mm genuine diamonds.

Piece Size:  Length / 9.9mm -  Width / 4.7mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Atlas                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. A unique design consisting of a 2.8mm triangle crystal with a 2mm round stone above.  

Piece Size:  Length / 6.4mm -  Width / 4.5mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Evie                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. Evie flower consists of genuine stones. The center is a 3mm white topaz stone surrounded by 1.2mm prong set diamonds. 

Piece Size:  Length / 6.4mm -  Width / 6.4mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Clara                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. Clara is a pear-shaped gold cast made out of solid 14kt. A 5mm round crystal stone is set below in a unique tension setting.

Piece Size:  Length / 9.8mm -  Width / 5mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Aquar                                                                               Made out of Nickle free solid 14kt Gold & implant grade steel pin. Aquar consists of a 5mm prong set baguette crystal stone. Dressed below with a 3mm aqua marquise stone and 4 round 1mm stones.

Piece Size:  Length / 11.3mm -  Width / 6.1mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Ruby                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. Ruby consists of a 5.8mm baguette stone surrounded by a cast of solid gold. Below is a 1.5mm ruby colored stone.

Piece Size:  Length / 9.3mm -  Width / 5.1mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Lola                                                                               Made out of Nickle free solid 14kt Gold & implant grade steel pin. Lola is made of 4 marquise crystals. Each stone is 3.0mm by 1.6mm. The above ball is 1.9mm made of solid gold.

Piece Size:  Length / 9.8mm -  Width / 5.5mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Mato                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. Mato is a pyramid shape with 4 faces with a height rise of 1.6mm.

Piece Size:  Length / 3.8mm  -  Width / 3.8mm - Square form

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Sakari                                                                             Made out of Nickle free solid 14kt Gold & implant grade steel pin. Sakari is made of 2 parts. The First part is a solid 14kt gold bar 5mm long and 1.6mm wide. The second part is a dangle chain dressed with genuine diamonds and at 9mm long. 

Piece Size:  Length / 15.2mm  -  Width / 1.5mm 

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Marta Right                                                                     Made out of Nickle free solid 14kt Gold & implant grade steel pin. Three marquise stones alongside a 2mm round prong set crystal. 

Piece Size:  Length / 7.5mm  -  Width / 4.3mm 

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Attachment - Ada                                                                                 Made out of Nickle free solid 14kt Gold & implant grade steel pin. Diamond shaped solid gold design surrounding a 3mm crystal stone.

Piece Size:  Length / 6.3mm  -  Width / 6.3mm - Square form

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Sword Attachment                                                                               Made out of solid 14kt Gold & implant grade steel pin. Tip to tip the beautify detailed sword is 9.1mm long and 4.3mm wide.

Piece Size:  Length / 9.1mm  -  Width / 4.3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Moon & Opal Attachment                                                                Made out of solid 14kt Gold & implant grade steel pin. Jeweled with 1.5mm white fire cultured opal.

Piece Size:  Length / 3.3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

14kt Gold Threadless Lightening Attachment                                                                      Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 8.9mm  -  Width / 2mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.