Diamonds and Precious Stones
14kt Gold Threadless Attachment - Emer
14kt Gold Threadless Attachment - Emer Made out of Nickle free solid 14kt Gold & implant grade steel pin. Emer is a 5.7mm round ring of genuine blue diamonds consisting of 16 prong set 1.2mm stones.
Piece Size: Length / 5.7mm - Width / 5.7mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Nyla
14kt Gold Threadless Attachment - Nyla Made out of Nickle free solid 14kt Gold & implant grade steel pin. Nyla is adorned with genuine 1.2mm diamond stones centered around a 2mm Garnet gemstone.
Piece Size: Length / 6.1mm - Width / 6.1mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Sakari
14kt Gold Threadless Attachment - Sakari Made out of Nickle free solid 14kt Gold & implant grade steel pin. Sakari is made of 2 parts. The First part is a solid 14kt gold bar 5mm long and 1.6mm wide. The second part is a dangle chain dressed with genuine diamonds and at 9mm long.
Piece Size: Length / 15.2mm - Width / 1.5mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Enola
14kt Gold Threadless Attachment - Enola Made out of Nickle free solid 14kt Gold & implant grade steel pin. Pear shaped, Elona is made with 5 genuine 1.3mm diamonds.
Piece Size: Length / 6mm - Width / 4.8mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Kaya
14kt Gold Threadless Attachment - Kaya Made out of Nickle free solid 14kt Gold & implant grade steel pin. Kaya is an arrow shape solid gold diamond incrusted piece consisting of ten 0.9mm genuine diamonds.
Piece Size: Length / 9.9mm - Width / 4.7mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Evie
14kt Gold Threadless Attachment - Evie Made out of Nickle free solid 14kt Gold & implant grade steel pin. Evie flower consists of genuine stones. The center is a 3mm white topaz stone surrounded by 1.2mm prong set diamonds.
Piece Size: Length / 6.4mm - Width / 6.4mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.