Threadless
Threadless Jeweled Pyramid Attachment
Threadless Jeweled Pyramid Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Ring With 2.5mm Jewel Attachment
Threadless Ring With 2.5mm Jewel Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Marquise Stone Attachment
24kt Gold PVD Titanium Threadless Marquise Stone Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Titanium Threadless Nose Labret - Disk
Trident Titanium Threadless Nose Labret 1.0mm x 8mm x 2.5mm Disk
Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless - Cat
14kt Gold Threadless - Cat Made out of Nickle free solid 14kt Gold & implant grade steel pin.
Piece Size: Length / 3.6mm - Width / 4.0mm
- Black Crystal Size: 2.0mm x 1pcs
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Lotus With Opal Attachment
Threadless Lotus With Opal Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Snake with Crystal Eye Attachment
Threadless Snake with Crystal Eye Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Gold Snake with Crystal Eye Attachment
24kt Gold PVD Titanium Threadless Gold Snake with Crystal Eye Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Solid Gold Chain
Trident 14kt Solid Gold Chain With 2mm O-Rings On Each End
Piece sizes:
- 16mm Length
- 22mm Length
- 40mm Length
24kt Gold PVD Titanium Threadless Butterfly Attachment
24kt Gold PVD Titanium Threadless Plain Butterfly Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Jewel Butterfly Attachment
24kt Gold PVD Titanium Threadless Jewel Butterfly Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Butterfly Attachment
Threadless Plain Butterfly Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Jeweled Butterfly Attachment
Threadless Jeweled Butterfly Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Trio Mini Attachment
24kt Gold PVD Titanium Threadless Trio Mini 4mm Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 5 Stone Curved Crown Attachment
Threadless 5 Stone Curved Crown Attachment
- Size: 3.2mm x 10.3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless 5 Stone Curved Crown Attachment
24kt Gold PVD Titanium Threadless Titanium 5 Stone Curved Crown Attachment
- Size: 3.2mm x 10.3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Triforce Attachment
Threadless Triforce Attachment
- Size: 6mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Triforce Attachment
24kt Gold PVD Titanium Threadless Triforce Attachment
- Size: 6mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Marquise Stone w CZ Attachment
24kt Gold PVD Titanium Threadless Marquise Stone w CZ Attachment
-
Marquise Size: 2.5mm x 5mm
- Round Stone Size: 1.5mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Marquise Stone w CZ Attachment
Threadless Marquise Stone w CZ Attachment
-
Marquise Size: 2.5mm x 5mm
- Round Stones Size: 1.5mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Dangle 2 Round Stones w Baguette Attachment
24kt Gold PVD Titanium Threadless Dangle 2 Round Stones w Baguette Attachment
-
Round Stone Size: 2mm
-
Baguette Size: 1.5mm x 3mm
-
Overall Size: 12mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Dangle 2 Round Stones w Baguette Attachment
Threadless Dangle 2 Round Stones w Baguette Attachment
-
Round Stone Size: 2mm
-
Baguette Size: 1.5mm x 3mm
-
Overall Size: 12mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Dangle Round Stones Attachment
24kt Gold PVD Titanium Threadless Dangle Round Stones Attachment
- Top Crystal Size: 3mm
-
Bottom Crystal Size: 3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Dangle Round Stones Attachment
Threadless Dangle Round Stones Attachment
- Top Crystal Size: 3mm
- Bottom Crystal Size: 3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Baguette and Round Stones Crown Attachment
24kt Gold PVD Titanium Threadless Baguette and Round Stones Crown Attachment
- Size: 5mm x 11mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Baguette and Round Stones Crown Attachment
Threadless Baguette and Round Stones Crown Attachment
- Size: 5mm x 11mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Rupee Attachment
24kt Gold PVD Titanium Threadless Rupee Attachment
- Size: 2.8mm x 6.7mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Rupee Attachment
Threadless Rupee Attachment
- Size: 2.8mm x 6.7mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless 2 Baguette Attachment
24kt Gold PVD Titanium Threadless 2 Baguette Attachment
- Size: 1.5mm x 3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 2 Baguette Attachment
Threadless 2 Baguette Attachment
- Size: 1.5mm x 3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
24kt Gold PVD Titanium Threadless Sword Dangle w Oval CZ Attachment
24kt Gold PVD Titanium Threadless Sword Dangle w Oval CZ Attachment
- Sword Size: 10mm
- Crystal Size: 1.5mm x 3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Sword Dangle w CZ Oval Attachment
Threadless Sword Dangle w CZ Oval Attachment
- Sword Size: 10mm
- Crystal Size: 1.5mm x 3mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.