Threadless
Threadless Cluster Jewel Attachment - 2 Jewelled Beaded Ovate
Trident Threadless Cluster Jewel Attachment - 2 Jeweled Beaded Ovate
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Cluster Jewel Attachment - Tear Crown
Trident Threadless Cluster Jewel Attachment - Tear Crown
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Cluster Jewel Attachment - Beaded Ovate
Trident Threadless Cluster Jewel Attachment - Beaded Ovate
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Cluster Jewel Attachment - Triple Marquise
Trident Threadless Cluster Jewel Attachment -Triple Marquise
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Moons Star Attachment w Opal
Trident Threadless Moons Star Attachment w Opal
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Jeweled Attachment Bijou
Trident Threadless Jeweled Attachment - Bijou
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Jeweled Ovate Attachment
Trident Threadless Jeweled Attachment - Ovate
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Jeweled Pyrus Attachment
Trident Threadless Jeweled Attachment - Pyrus
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 5 Prong Jeweled Rectangular Cut Attachment
Trident Threadless 5 Prong Jeweled Rectangular Cut Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 5 Prong Set Ovate Jeweled Attachment
Trident Threadless 5 Prong Set Crown Ovate Jeweled Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Moonstar Attachment w Crystal
Trident Titanium Threadless Moonstar Attachment w Crystal
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Rainbow Jeweled 5 Prong Attachment
Threadless Rainbow Jeweled 5 Prong Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Jeweled Cross Attachment
Threadless Jeweled Cross Attachment 6mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 6 Petal Flower Jeweled Attachment
Threadless 6 Petal Flower Jeweled Attachment 6mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 4mm Jeweled Dangle Bezel Attachment
Trident Threadless 4mm Jeweled Dangle 3mm Bezel Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless Curved Jeweled Bar Attachment
Threadless Curved Jeweled Bar Attachment 6.5mm
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 9 Stone Prong Set Attachment
Threadless 9 Stone Prong Set Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 9 Curved Prong Set Jeweled Attachment
Threadless 9 Curved Prong Set Jeweled Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Square Flower Threadless 4mm Jewel Attachment
Square Flower Threadless 4mm Jewel Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 4mm Jeweled Dangle Cross Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Cross Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 4mm Jeweled Dangle Ball Trio Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Ball Trio Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 4mm Jeweled Dangle Lightening Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Lightening Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Threadless 4mm Jeweled Dangle Moon Attachment
Trident Titanium Threadless 4mm Jeweled Dangle Moon Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
Trident Threadless Snow Flake Attachment
Trident Threadless Snow Flake Attachment
Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Olla
14kt Gold Threadless Attachment - Olla Right Made out of Nickle free solid 14kt Gold & implant grade steel pin. Olla is designed for the right ear but also versatile for multiple placements. Featured with a .9mm gold bar wrapping around to the rear. A 1.75mm round stone sits above the gold bar. Running adjacent a gold chain drop hanging 17.9mm. A unique design with elegance and sophistication.
Piece Size: Length / 17.9mm - Width / 6.7mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Gold Threadless Attachment - Olina
14kt Gold Threadless Attachment - Olina Left Made out of Nickle free solid 14kt Gold & implant grade steel pin. Olina is designed for the left ear but also versatile for multiple placements. Featured with a .9mm gold bar wrapping around to the rear. A 1.75mm round stone sits above the gold bar. Running adjacent a gold chain drop hanging 17.9mm. A unique design with elegance and sophistication.
Piece Size: Length / 17.9mm - Width / 6.7mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.
14kt Solid Gold Earring Cuff - Issa Right
14kt Solid Gold Earring With 5 Prong Set Princess Crystals - Issa Right Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Designed around 5 prong set 2mm princess cut crystals along a 1mm solid gold band. Issa is petit and elegant.
Piece Size: Length / 11.3mm - Width / 11.3mm
Bar Gauge: 0.80mm / 20GA Length 6mm Internal Ring Size - 8.8mm
14kt Solid Gold Earring Cuff - Issa Left
14kt Solid Gold Earring With 5 Prong Set Princess Crystals - Issa Left Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Designed around 5 prong set 2mm princess cut crystals along a 1mm solid gold band. Issa is petit and elegant.
Piece Size: Length / 11.3mm - Width / 11.3mm
Bar Gauge: 0.80mm / 20GA Length 6mm Internal Ring Size - 8.8mm
14kt Solid Gold Earring - Alva
14kt Solid Gold Earring With 5 Prong Set Crystals - Alva Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Alva is a solid gold 1.55mm thick ring with a drop hanging 30mm solid gold bar.
Piece Size: Length / 11.75mm - Width / 11.75mm
Bar Gauge: 0.80mm / 20GA Length 5.2mm Internal Ring Size 9.4mm
14kt Solid Gold Earring - Yana
14kt Solid Gold Earring With 5 Prong Set Crystals - Yana Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Yana is a petit earing with five 1.7mm prong set crystals front facing followed by a 1.4mm gold band towards the rear.
Piece Size: Length / 8.7mm - Width / 8.7mm
Bar Gauge: 0.70mm / 21GA Length 4.3mm Internal Ring Size 6mm
14kt Solid Gold Earring - Rassa
14kt Solid Gold Earring Cuff & Chain - Rassa Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Rassa is designed as a petit ear cuff at 1.9mm in thickness. Drop hanging at 11.5mm length a delicate solid 14kt chain to slight wrap around the ear placement.
Piece Size: Length / 9.3mm - Width / 9.3mm
Bar Gauge: 0.90mm / 19GA Length 5.5mm Internal Ring Size 6.8mm
14kt Gold Threadless Attachment - Diana Right
14kt Gold Threadless Attachment - Diana Right Made out of Nickle free solid 14kt Gold & implant grade steel pin. Diana is one the smaller of the two cross designs offered. With a 6.2mm length and 1.15mm thickness crystal incrusted bar across a 12.9mm length & 0.8mm thickness solid gold bar.
Piece Size: Length / 12.9mm - Width / 4mm
Pin Gauge: 0.42mm / Length: 4mm*
Threadless Jewelry Method:
Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:
- Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
- Slightly bend the insertion pin within the bar.
- Push the end into the shaft and test the fit.
Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.