Threadless Titanium Duo Marquise w Chain Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Titanium Duo Round Stones Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Titanium Marquise Stone w Dangle Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless 2 Marquise w Dangle Stone Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless 2 Marquise with Centre Stone Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Jeweled Pyramid Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Ring With 2.5mm Jewel Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Marquise Stone Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Internally Threaded Attachment Trio Marquise Attachment 0.9mm (16GA)

• Size: 8.2mm x 3.4mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Lotus With Opal Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Snake with Crystal Eye Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Gold Snake with Crystal Eye Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Plain Butterfly Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Jewel Butterfly Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Plain Butterfly Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Jeweled Butterfly Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Trio Mini 4mm Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless 5 Stone Curved Crown Attachment

• Size: 3.2mm x 10.3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Titanium 5 Stone Curved Crown Attachment

•  Size: 3.2mm x 10.3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Triforce Attachment

• Size: 6mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Triforce Attachment

• Size: 6mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Marquise Stone w CZ Attachment

• Marquise Size: 2.5mm x 5mm
  
• Round Stone Size: 1.5mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Marquise Stone w CZ Attachment

• Marquise Size: 2.5mm x 5mm
  
• Round Stones Size: 1.5mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Dangle 2 Round Stones w Baguette Attachment

• Round Stone Size: 2mm
  
• Baguette Size: 1.5mm x 3mm
  
• Overall Size: 12mm
  

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Dangle 2 Round Stones w Baguette Attachment

• Round Stone Size: 2mm
  
• Baguette Size: 1.5mm x 3mm
  
• Overall Size: 12mm
  

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Dangle Round Stones Attachment

• Top Crystal Size: 3mm
• Bottom Crystal Size: 3mm
  

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Dangle Round Stones Attachment

• Top Crystal Size: 3mm
• Bottom Crystal Size: 3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Baguette and Round Stones Crown Attachment

• Size: 5mm x 11mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Baguette and Round Stones Crown Attachment

• Size: 5mm x 11mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Rupee Attachment

• Size: 2.8mm x 6.7mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Rupee Attachment

• Size: 2.8mm x 6.7mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless 2 Baguette Attachment

• Size: 1.5mm x 3mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.