Trident 14kt Solid Gold Chain With 2mm O-Rings On Each End

Piece sizes:

• 16mm Length
• 22mm Length
• 40mm Length

14kt Gold Threadless - Ankh                                                                                         Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 6.0mm  -  Width / 3.6mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - 3 Petal Marquise                                                                             Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Super Small & Delicate Length / 2.1mm  -  Width / 3.5mm

Crystal Size: 0.9mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Disk Attachment                                                                                Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Feather                                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 6.0mm  -  Width / 2.0mm

Crystal Size: 1.1mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Cross                                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3.9mm  -  Width / 2.1mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Love Heart                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 2.7mm  -  Width / 2.9mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Taurus                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 4.6mm  -  Width / 5.1mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Aquarius                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 5.5mm  -  Width / 3.7mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Pisces                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 4.6mm  -  Width / 3.8mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Aries                                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 4.8mm  -  Width / 4.1mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Capricorn                                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 4.8mm  -  Width / 3.8mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Gemini                                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 4.7mm  -  Width / 3.5mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Cancer                                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 5.3mm  -  Width / 4.2mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Leo                                                                                            Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 4.7mm  -  Width / 3.6mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Virgo                                                                                            Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 5.1mm  -  Width / 4.8mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Libra                                                                                            Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 5.8mm  -  Width / 4.3mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Scorpio                                                                                            Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 4.7mm  -  Width / 4.7mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Sagittarius                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 5.3mm  -  Width / 4.2mm

• Crystal Size: 1.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Lunar Attachment                                                                              Made out of solid 14kt Gold & implant grade steel pin. The 3 balls aside the crescent are 1mm each.

Piece Size:  Length / 3.4mm  -  Width / 3.5mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Gold 14kt Threadless Attachment Jeweled 3mm Bezel                                                    Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Star With Jewel                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 2.7mm  -  Width / 2.7mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - CZ With Dangle Cross                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 6.3mm  -  Width / 2.1mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Teddy With Jewel                                                                              Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.3mm  -  Width / 2.4mm

• Crystal Size: 1.1mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Hollow Heart                                                                                     Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.1mm  -  Width / 3.6mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Mouse                                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.6mm  -  Width / 4.0mm

• Black Crystal Size: 2.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Cat                                                                                              Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.6mm  -  Width / 4.0mm

• Black Crystal Size: 2.0mm x 1pcs

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Opal Attachment                                                                               Made out of solid 14kt Gold & implant grade steel pin. 4mm white fire cultured opal embedded in a solid 14kt gold cast.

Piece Size:  Length / 4mm  -  Width / 4mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Ring Attachment                                                                              Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 5.8mm  -  Width / 4.2mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Shark                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 6.9mm  -  Width / 3.8mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Eye With Blue Crystal                                                                    Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.5mm  -  Width / 2.2mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Flat Moon                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. 

Piece Size: Length / 3.8mm  -  Width / 3.3mm

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.