White 14kt Gold Threadless Jewel Sword                                                                              Made out of solid 14kt Gold & implant grade steel pin. Tip to tip the beautify detailed sword is 9.1mm long and 4.3mm wide.

Piece Size:  Length / 9.1mm  -  Width / 4.3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

White 14kt Gold Threadless Moon & Opal                                                                                Made out of solid 14kt Gold & implant grade steel pin. Jeweled with 1.5mm white fire cultured opal.

Piece Size:  Length / 3.3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

White 14kt Gold Threadless Lunar                                                                                        Made out of solid 14kt Gold & implant grade steel pin. The 3 balls aside the crescent are 1mm each.

Piece Size:  Length / 3.4mm  -  Width / 3.5mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

White Gold 14kt Threadless Jeweled Bezel                                                                            Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless White Fire Opal And Crystal Prong Set Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136) 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Marquise with 5 Round Stones Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless 5 Marquise Stone Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Internally Threaded Marquis with 4 Stones Prong Set Attachment 

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136) 

Threadless 5 Leaf Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Trio Diamond Shape Fan Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Internally Threaded Disk Attachment 0.9mm (For 16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Internally Threaded Spike 3mm Attachment 0.9mm (For 16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Internally Threaded Sword Attachment 0.9mm (For 16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

24kt Gold PVD Titanium Threadless Crowned Tear 3mm Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Marquise Trio Red, Clear, Purple Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Marquise Trio Aqua, Orange, Yellow Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Threadless Marquise Trio Green, Blue, Clear Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Marquise Trio Aqua, Clear, Red Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless 3 Leaf Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Marquise Trio Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Titanium Moon Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Crescent Moon Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Tear Hinged Ring w 2.5mm Jewel 1.2mm x 8mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident 24kt Gold PVD Titanium Threadless Cluster 2.5mm Crystal Attachment

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Gold PVD Titanium Threadless Moonstar Attachment w Crystal Attachment

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Bee With Crystal Wings Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Threadless Snake Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

24kt Gold PVD Titanium Internally Threaded 10 Petal Jeweled Flower Attachment 0.9mm (16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

24kt Gold PVD Titanium Internally Threaded Moon Attachment 0.9mm (16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.

Trident Titanium Internally Threaded Jeweled Ovate Flower Attachment 0.9mm (For 16G)

Internally Threaded Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

24kt Gold PVD Titanium Internally Threaded Labret Pin

16GA / 1.2mm -  3mm Base

16GA / 1.2mm -  4mm Base

Internally Threaded Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

PVD (Vacuum coating), also known as thin-film deposition, is a vacuum chamber process whereby a very thin and steady layer of coating is applied to the titanium surface of a substrate, protecting it from forces that might wear it down or decrease its efficiency.

PVD Coating isn’t adding another layer to the object that will chip or crack with time (think old paint).

PVD coating is becoming a standard for medical tools. The coating reduces friction, provides biocompatibility for implants, is antimicrobial, and it serves as a chemical barrier for those with a sensitivity to nickel (which can often be found in the tool).

As opposed to other coatings that chip, crack, and wear down, vacuum coatings are a shining armor for your jewelry, providing a strong and thin coating for a variety of applications.  

Unlike paints which other companies use and many other methods, this technique is body-friendly so it can be used safely and without a problem.