14kt Gold Threadless - Marta Right                                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. Three marquise stones alongside a 2mm round prong set crystal. 

Piece Size:  Length / 7.5mm  -  Width / 4.3mm 

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Marta Left                                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. Three marquise stones alongside a 2mm round prong set crystal. 

Piece Size:  Length / 7.5mm  -  Width / 4.3mm 

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Disk Attachment                                                                                Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 3mm  -  Width / 3mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Bijou                                                                                                  Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 4.7mm  -  Width / 2.2mm

Pin Size: 0.45mm / Length: 4mm

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Flower                                                                                                Made out of solid 14kt Gold & implant grade steel pin. Jeweled with 6 crystals surrounding solid gold disk.

Piece Size:  Length / 4.7mm  -  Width / 4.7mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Opal                                                                                                  Made out of solid 14kt Gold & implant grade steel pin. 4mm white fire cultured opal embedded in a solid 14kt gold cast.

Piece Size:  Length / 4mm  -  Width / 4mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Serotonin                                                                                          Made out of solid 14kt Gold & implant grade steel pin. Perfectly molded with 2 crystals prong set at 1.0mm in size.    

Piece Size:  Length / 11mm  -  Width / 4.5mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Black Spike                                                                                        Made out of solid 14kt Gold & implant grade steel pin. 

Piece Size:  Length / 5mm  -  Width / 2.4mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Earring Cuff & Chain - Rassa                                                                                      Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Rassa is designed as a petit ear cuff at 1.9mm in thickness. Drop hanging at 11.5mm length a delicate solid 14kt chain to slight wrap around the ear placement. 

Piece Size:  Length / 9.3mm -  Width / 9.3mm 

Bar Gauge: 0.90mm / 19GA     Length 5.5mm                                                                      Internal Ring Size 6.8mm

14kt Gold Threadless - Nina                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. Nina features 10 round 1.0mm crystals prong set into solid 14kt gold

Piece Size:  Length / 9.8mm  -  Width / 3.3mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless- Enola                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. Pear shaped, Elona is made with 5 genuine 1.3mm diamonds.  

Piece Size:  Length / 6mm -  Width / 4.8mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Navi                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. Navi is made up of three 2mm round crystals on the main 14kt gold bar. Hanging below are 2 separate flat solid gold chains. 

Piece Size:  Length / 30mm -  Width / 2.4mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Kaya                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. Kaya is an arrow shape solid gold diamond incrusted piece consisting of ten 0.9mm genuine diamonds.

Piece Size:  Length / 9.9mm -  Width / 4.7mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Rio                                                                                                    Made out of Nickle free solid 14kt Gold & implant grade steel pin. Rio is a triple marquise crystal prong set piece separated by 1.4mm solid gold balls. Each stone is 3mm long and 1.5mm wide.

Piece Size:  Length / 7.1mm -  Width / 4mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Arris                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. A princess cut 2mm prong set crystal.

Piece Size:  Length / 3mm -  Width / 3mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Evie                                                                                                    Made out of Nickle free solid 14kt Gold & implant grade steel pin. Evie flower consists of genuine stones. The center is a 3mm white topaz stone surrounded by 1.2mm prong set diamonds. 

Piece Size:  Length / 6.4mm -  Width / 6.4mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Ursa                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. 4.7mm star consisting of 6 round prong set 0.9mm crystals surrounding a solid 3mm gold center.

Piece Size:  Length / 4.7mm -  Width / 4.7mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Ada                                                                                                    Made out of Nickle free solid 14kt Gold & implant grade steel pin. Diamond shaped solid gold design surrounding a 3mm crystal stone.

Piece Size:  Length / 6.3mm  -  Width / 6.3mm - Square form

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Jeweled Rod                                                                                      Made out of solid 14kt Gold & implant grade steel pin. Jeweled with 6 crystals.

Piece Size:  Length / 6.7mm  -  Width / 1.1mm

Pin Size: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Earring With 5 Prong Set Princess Crystals - Issa Right                                            Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Designed around 5 prong set 2mm princess cut crystals along a 1mm solid gold band. Issa is petit and elegant.

Piece Size:  Length / 11.3mm -  Width / 11.3mm 

Bar Gauge: 0.80mm / 20GA     Length 6mm                                                                      Internal Ring Size - 8.8mm

14kt Gold Earring With 5 Prong Set Princess Crystals - Issa Left                                                Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Designed around 5 prong set 2mm princess cut crystals along a 1mm solid gold band. Issa is petit and elegant.

Piece Size:  Length / 11.3mm -  Width / 11.3mm 

Bar Gauge: 0.80mm / 20GA     Length 6mm                                                                      Internal Ring Size - 8.8mm

14kt Gold Earring Paved Crystals - Inu                                                                                      Made out of solid 14kt Yellow Gold Nickle Free on a hinge clasp. Inu is a complete paved crystal incrusted earring with 24 round stones front to back.

Piece Size:  Length / 13.9mm -  Width / 1.2mm 

Gauge: 0.80mm / 20GA                                                                                                          Internal Ring Size 10.6mm

14kt Gold Threadless - Olla - Right                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. Olla is designed for the right ear but also versatile for multiple placements. Featured with a .9mm gold bar wrapping around to the rear. A 1.75mm round stone sits above the gold bar. Running adjacent a gold chain drop hanging 17.9mm. A unique design with elegance and sophistication.      

Piece Size:  Length / 17.9mm  -  Width / 6.7mm 

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Olina - Left                                                                                        Made out of Nickle free solid 14kt Gold & implant grade steel pin. Olina is designed for the left ear but also versatile for multiple placements. Featured with a .9mm gold bar wrapping around to the rear. A 1.75mm round stone sits above the gold bar. Running adjacent a gold chain drop hanging 17.9mm. A unique design with elegance and sophistication.      

Piece Size:  Length / 17.9mm  -  Width / 6.7mm 

Pin Gauge: 0.42mm / Length: 4mm*

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Diana Right                                                                                      Made out of Nickle free solid 14kt Gold & implant grade steel pin. Diana is one the smaller of the two cross designs offered. With a 6.2mm length and 1.15mm thickness crystal incrusted bar across a 12.9mm length & 0.8mm thickness solid gold bar. 

Piece Size:  Length / 12.9mm -  Width / 4mm 

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Diana Left                                                                                          Made out of Nickle free solid 14kt Gold & implant grade steel pin. Diana is one the smaller of the two cross designs offered. With a 6.2mm length and 1.15mm thickness crystal incrusted bar across a 12.9mm length & 0.8mm thickness solid gold bar. 

Piece Size:  Length / 12.9mm -  Width / 4mm 

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Ring - Elsy                                                                                            Made out of solid 14kt Gold & implant grade steel pin. Elsy is designed as a petit ring but with the benefit of being threadless to allow it to fit into a labret for alternative placements. Elsy is the smaller option to the threadless ring designs with 13 round 1mm crystals pave the ring end to end .

Piece Size: Length / 7.6mm - Width / 1mm

Pin Gauge: 0.42mm / Length: 4mm*                                                                           Internal Ring Size - 5.1mm

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless Ring - Ella                                                                                            Made out of solid 14kt Gold & implant grade steel pin. Ella is the larger of the two threadless ring designs. Designed with the benefit of being threadless to allow it to fit into a labret for alternative placements. 22 round 1mm crystals pave the ring end to end.

Piece Size: Length / 12.8mm - Width / 1mm

Pin Gauge: 0.42mm / Length: 4mm*                                                                            Internal Ring Size - 10.3mm

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Lissa                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. A beautifully 5mm round woven solid gold ring surrounding a 2.8mm round crystal stone.

Piece Size:  Length / 5mm -  Width / 5mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Rinya                                                                                                Made out of Nickle free solid 14kt Gold & implant grade steel pin. Rinya is a bespoke design consisting of a jeweled 6 crystal solid gold bar with draping flat style chain. 

Piece Size:  Length / 37.4mm -  Width / 6.5mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Linya                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. Linya is a bespoke design consisting of a jeweled 6 crystal solid gold bar with draping flat style chain. 

Piece Size:  Length / 37.4mm -  Width / 6.5mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

14kt Gold Threadless - Ruby                                                                                                  Made out of Nickle free solid 14kt Gold & implant grade steel pin. Ruby consists of a 5.8mm baguette stone surrounded by a cast of solid gold. Below is a 1.5mm ruby colored stone.

Piece Size:  Length / 9.3mm -  Width / 5.1mm

Pin Gauge: 0.42mm / Length: 4mm* 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.